Keysight Agilent MSOX4034A

98 Visitors viewed Testwall Ltd ads in the last 30 Days

Oscilloscope, 350 MHz 4 + 6 Chs.

Keysight MSOX4034A (Agilent) Oscilloscope The Keysight MSOX4034A is a four-channel model in the InfiniiVision 4000 X-Series, providing innovative touch triggering. It is surprisingly easy to use with its large, state-of-the-art capacitive touch screen. The MSOX4034A Oscilloscope is fully upgradable, including bandwidth, and its unique 5-instruments-in-one design, provides superior performance, speed, and functionality.Features and Specifications of the Keysight MSOX4034A (Agilent) Oscilloscope include:Features of the Agilent MSOX4034A include:

• Oscilloscope  
• Logic Analyser (MSO) 
• Serial protocol Analyser, including USB (optional)
• WaveGen 20 MHz dual channel arbitrary/function generator (optional)
• Digital voltmeter (DVM) option:
• with 3-digit voltage
• with 5-digit frequency counter measurements

• with 3-digit voltage
• with 5-digit frequency counter measurements

Specifications of the Keysight MSOX4034A include:

• 4 analog
• 16 digital

• 5 GSa/s half channel
• 2.5 GSa/s all channel

• Hardware bandwidth limits:  Approximately 20 MHz (selectable)
• Input coupling:  AC, DC
• Input impedance:  Selectable:  
• 1 MΩ ± 1% (16 pF)
• 50 Ω ± 1.5%
• Input sensitivity range:  1mV/div to 5 V/div (1 MΩ and 50 Ω)
• Vertical resolution:  8 bits (measurement resolution is 12 bits with averaging)
• Maximum input voltage:
• 300 Vrms, 400 Vpk
• Transient overvoltage 1.6 kVpk
• With N2862A, N2863A, N2890A 10:1 probe: 300 Vrms
• Frequency de-rating (assumes sine wave input): 400 Vpk until 40 kHz, then de-rates at 20 dB/dec until 6 Vpk
• DC vertical gain accuracy: ± 2.0% full scale
• DC vertical offset accuracy:  ± 0.1 div ± 2 mV ± 1% of offset setting
• Channel-to-channel isolation: ≥ 40 dB from DC to maximum specified bandwidth of each model
• Offset range:
• ± 5 V (< 10 mV/div)
• ± 20 V (10 to 200 mV/div)
• ± 75 V (> 200 mV/div)

• Digital input channels:  16 digital (D0 to D15. pod 1:D7 ~ D0, Pod 2: D15 ~ D8)
• Thresholds: Threshold per pod
• Threshold selections:  TTL (+1.4 V), 5V CMOS (+2.5 V), ECL (-1.3 V), user-defined (selectable by pod)
• User-defined threshold range:  ± 8.0 V in 10 mV steps
• Maximum input voltage:  ± 40 V peak CAT l; transient overvoltage 800 Vpk
• Threshold accuracy:  ± (100 mV + 3% of threshold setting)
• Maximum input dynamic range:  ± 10 V about threshold
• Minimum voltage swing:  500 mVpp
• Input impedance:  100 kΩ ± 2% at probe tip
• Input capacitance:  ~8 pF
• Vertical resolution: 1 bit

• Time base range:  2 ns/div to 50 s/div
• Time base accuracy:  ± 10 ppm
• Time base delay time range:
• Pre-trigger:  Greater of 1 screen width or 200 μs (400 μs in interleaving mode)
• Post-trigger: 1 s to 500 s
• Channel-to-channel deskew range:  ± 100 ns
• Δ Time accuracy (using cursors):  ± 0.001% of reading ± 0.16% screen width ± 30pS
• Modes:  Main, zoom, roll, XY
• XY:
• On channels 1 and 2 only
• Z Blanking on ext trigger input, 1.4 V threshold  
• Bandwidth:  Maximum bandwidth
• Phase error at 1 MHz: < 0.5 degree
• Time base: 200 ns/div to 50 ms/div

• Minimum detectable pulse width:  2 ns
• Channel-to-channel skew:
• 2 ns (typical)
• 3 ns (maximum)

• Maximum analog channels sample rate:  
• 5 GSa/s half channel interleaved
• 2.5 GSa/s all channel
• Maximum analog channels record length:
• 4 Mpts half channel interleaved
• 2 Mpts all channel
• Maximum digital channels sample rate:  1.25 GSa/s
• Maximum digital channels record length:  2 Mpts (with digital channels only)
• Modes:
• Normal:  Default mode
• Peak detect:  Capture glitches as narrow as 200 ps at all time base settings
• Averaging:  Selectable from 2, 4, 8, 16, 64, … to 65,536
• High resolution:
• Real time boxcar averaging reduces random noise and effectively increases vertical resolution
• 12 bits:  ≥ 50 μs/div
• 11 bits:  ≥ 20 μs/div
• 10 bits:  ≥ 10 μs/div
• 9 bits:  ≥ 5 μs/div
• Segmented:
• Segmented memory optimizes available memory for data streams that have long dead times between activity
• Maximum segments = 1000
• Re-arm time = 1 μs (minimum time between trigger events)
• Re-arm time when use with the InfiniiScan Zone = 65 us or faster (typical)
• Roll:  
• Displays the waveform moving across the screen from right to left
• Available at the time base 50 ms/div or slower

• Trigger sources:  Analog channel  (1~4), digital channel (D0~D15), line, external, WaveGen (1 or mod) (FM/FSK)
• Trigger modes:
• Normal: Requires trigger event for scope to trigger
• Auto : Triggers automatically in absence of trigger event
• Single:
• Front panel button that triggers only once on a trigger event
• Press [Single] button again for scope to find another trigger event, or press [Run] front-panel button to trigger continuously in either Auto or Normal mode
• Force:  Front panel button that forces a trigger
• Trigger coupling:  
• DC: DC coupled trigger
• AC: AC coupled trigger, cutoff frequency: < 10 Hz (internal); < 50 Hz (external)
• High frequency reject:  Cutoff frequency ~ 50 kHz
• Low frequency reject:  Cutoff frequency ~ 50 kHz 
• Noise reject:
• Adds hysteresis to the trigger circuitry
• Selectable OFF or ON
• Decreases sensitivity 2x
• Trigger holdoff range: 40 ns to 10.00 s  
• Trigger sensitivity:
• Internal:
• < 10 mV/div: greater of 1 div or 5 mV
• ≥ 10 mV/div: 0.6 div
• External:
• ± 1.6 V:  
• 40 mVpp DC to 100 MHz
• 70 mVpp 100 MHz to 200 MHz
• ± 8 V:  
• 200 mVpp DC to 100 MHz
• 350 mVpp 100 MHz to 200 MHz
• Trigger level range:
• Any channel:  ± 6 div from center screen
• External:  
• ± 8 V range = ± 8 V
• ± 1.6 V range = ± 1.6 V

• USB 2.0 hi-speed host port:
• x3 ports, 2 front and one rear panel
• Supports memory devices, printers, keybords and mice
• USB 2.0 hi-speed device port:
• One port on rear panel
• USB Test & Measurement Class (USBTMC) compatible
• LAN port:
• 10/100Base-T port on rear panel
• LXI IPv6 extended function
• Web remote control:  VNC Web interface (via major Web browsers)
• Video out port:  
• SVGA out on rear panel
• Connect Oscilloscope display to an external monitor or projector
• GPIB port:  N4865A GPIB-to-LAN adapter (optional)
• 10 MHz out/in:  
• BNC connector on the rear panel
• Suported modes:  Off, 10 MHz out, or reference signal mode (10 MHz in)
• Trigger out:  
• BNC connecter on the rear panel 
• Supported modes:  triggers, mask, waveform generator 1 sync pulse, and waverform generator 2 sync pulse

• 1 MΩ ± 1% (16 pF)
• 50 Ω ± 1.5%

• 300 Vrms, 400 Vpk
• Transient overvoltage 1.6 kVpk
• With N2862A, N2863A, N2890A 10:1 probe: 300 Vrms
• Frequency de-rating (assumes sine wave input): 400 Vpk until 40 kHz, then de-rates at 20 dB/dec until 6 Vpk

• ± 5 V (< 10 mV/div)
• ± 20 V (10 to 200 mV/div)
• ± 75 V (> 200 mV/div)

• Pre-trigger:  Greater of 1 screen width or 200 μs (400 μs in interleaving mode)
• Post-trigger: 1 s to 500 s

• On channels 1 and 2 only
• Z Blanking on ext trigger input, 1.4 V threshold  
• Bandwidth:  Maximum bandwidth
• Phase error at 1 MHz: < 0.5 degree
• Time base: 200 ns/div to 50 ms/div

• 2 ns (typical)
• 3 ns (maximum)

• 5 GSa/s half channel interleaved
• 2.5 GSa/s all channel

• 4 Mpts half channel interleaved
• 2 Mpts all channel

• Normal:  Default mode
• Peak detect:  Capture glitches as narrow as 200 ps at all time base settings
• Averaging:  Selectable from 2, 4, 8, 16, 64, … to 65,536
• High resolution:
• Real time boxcar averaging reduces random noise and effectively increases vertical resolution
• 12 bits:  ≥ 50 μs/div
• 11 bits:  ≥ 20 μs/div
• 10 bits:  ≥ 10 μs/div
• 9 bits:  ≥ 5 μs/div
• Segmented:
• Segmented memory optimizes available memory for data streams that have long dead times between activity
• Maximum segments = 1000
• Re-arm time = 1 μs (minimum time between trigger events)
• Re-arm time when use with the InfiniiScan Zone = 65 us or faster (typical)
• Roll:  
• Displays the waveform moving across the screen from right to left
• Available at the time base 50 ms/div or slower

• Real time boxcar averaging reduces random noise and effectively increases vertical resolution
• 12 bits:  ≥ 50 μs/div
• 11 bits:  ≥ 20 μs/div
• 10 bits:  ≥ 10 μs/div
• 9 bits:  ≥ 5 μs/div

• Segmented memory optimizes available memory for data streams that have long dead times between activity
• Maximum segments = 1000
• Re-arm time = 1 μs (minimum time between trigger events)
• Re-arm time when use with the InfiniiScan Zone = 65 us or faster (typical)

• Displays the waveform moving across the screen from right to left
• Available at the time base 50 ms/div or slower

• Normal: Requires trigger event for scope to trigger
• Auto : Triggers automatically in absence of trigger event
• Single:
• Front panel button that triggers only once on a trigger event
• Press [Single] button again for scope to find another trigger event, or press [Run] front-panel button to trigger continuously in either Auto or Normal mode
• Force:  Front panel button that forces a trigger

• DC: DC coupled trigger
• AC: AC coupled trigger, cutoff frequency: < 10 Hz (internal); < 50 Hz (external)
• High frequency reject:  Cutoff frequency ~ 50 kHz
• Low frequency reject:  Cutoff frequency ~ 50 kHz 
• Noise reject:
• Adds hysteresis to the trigger circuitry
• Selectable OFF or ON
• Decreases sensitivity 2x

• Internal:
• < 10 mV/div: greater of 1 div or 5 mV
• ≥ 10 mV/div: 0.6 div
• External:
• ± 1.6 V:  
• 40 mVpp DC to 100 MHz
• 70 mVpp 100 MHz to 200 MHz
• ± 8 V:  
• 200 mVpp DC to 100 MHz
• 350 mVpp 100 MHz to 200 MHz

• Any channel:  ± 6 div from center screen
• External:  
• ± 8 V range = ± 8 V
• ± 1.6 V range = ± 1.6 V

• Front panel button that triggers only once on a trigger event
• Press [Single] button again for scope to find another trigger event, or press [Run] front-panel button to trigger continuously in either Auto or Normal mode

• Adds hysteresis to the trigger circuitry
• Selectable OFF or ON
• Decreases sensitivity 2x

• < 10 mV/div: greater of 1 div or 5 mV
• ≥ 10 mV/div: 0.6 div

• ± 1.6 V:  
• 40 mVpp DC to 100 MHz
• 70 mVpp 100 MHz to 200 MHz
• ± 8 V:  
• 200 mVpp DC to 100 MHz
• 350 mVpp 100 MHz to 200 MHz

• 40 mVpp DC to 100 MHz
• 70 mVpp 100 MHz to 200 MHz

• 200 mVpp DC to 100 MHz
• 350 mVpp 100 MHz to 200 MHz

• ± 8 V range = ± 8 V
• ± 1.6 V range = ± 1.6 V

• x3 ports, 2 front and one rear panel
• Supports memory devices, printers, keybords and mice

• One port on rear panel
• USB Test & Measurement Class (USBTMC) compatible

• 10/100Base-T port on rear panel
• LXI IPv6 extended function

• SVGA out on rear panel
• Connect Oscilloscope display to an external monitor or projector

• BNC connector on the rear panel
• Suported modes:  Off, 10 MHz out, or reference signal mode (10 MHz in)

• BNC connecter on the rear panel 
• Supported modes:  triggers, mask, waveform generator 1 sync pulse, and waverform generator 2 sync pulse