Showing Results for Keithley 7001

The Model 7001 is a half-rack, high density, two-slot mainframe that supports the widest range of signals in the test and measurement industry. DC switching capabilities from nanovolts to 1100 V and femtoamps to 5 A, as well as RF and optical switch support, make the Model 7001 a versatile production test tool for a wide array of applications.

Built-in scan control eliminates the need for the computer to control every step of the test procedure. Simply program the 7001 to control channel spacing, scan spacing, and the number of scans. A built-in non-volatile memory stores up to 100 complete switch patterns. You can include these memory locations as part of the scan list.

Each slot of the 7001 can accommodate up to 40 channels. This means fewer switch cards are required, reducing the amount of switching hardware needed. Higher density also provides extra capacity and flexibility.

The analog backplane of the 7001 is used by the high density switch cards. The backplane eliminates intercard wiring and increases configuration flexibility. Two cards can be connected through the backplane to create a 1×80 multiplexer, a 4×20 matrix, or a multiplexer/matrix combination that provides matrix row expansion.

• DC, RF, and optical switch capability
• Supports the broadest range of signals in the industry
• Integrates easily with DMM and SourceMeter® instruments
• Full channel status display
• 2 card slots
• Supports more than 30 switch/control cards
• Memory: Battery backed-up storage for 100 switch patterns
• Switch settling time: Automatically selected by the mainframe for each card
• Trigger sources: External Trigger (TTL-compatible, programmable edge, 600 ns minimum pulse, rear panel BNC), IEEE-488 bus (GET, *TRG), Trigger Link, Manual (front panel), Internal Timer, programmable from 1 ms to 99999.999 s in 1 ms increments
• Status output: Channel Ready (TTL-compatible signal, rear panel BNC). Low going pulse (10 μs typical) issued after relay settling time. For two different switch cards, 7001 will be set to the slowest relay settling time
• Switching sequence: Automatic break-before-make
• Mainframe digital I/O: 4 open-collector outputs (30 V maximum pull-up voltage, 100 mA maximum sink current, 10 Ω output impedance), 1 TTL compatible input, 1 common
• Relay drive: 700 mA maximum for both card slots
• Execution speed of scan list
  • Individual channels: With 7011 card - 130/second, with 7015 card - 500/second
  • Memory setups: With 7011 card - 125/second, with 7015 card - 450/second
• Analog backplane
  • Signals: Four 3-pole rows (Hi, Lo, Guard)
  • Maximum voltage: 250 VDC, 250 Vrms, 350 VAC peak, signal path to signal path or signal path to chassis
  • Maximum current: 1 A peak
  • Channel crosstalk: <–65 dB @ 1 MHz (50 Ω load)
  • Bandwidth: <3 dB loss at 100 MHz (50 Ω load)
• IEEE-488 bus implementation
  • Standards conformance: Conforms to SCPI-1990, IEEE-488.2, and IEEE-488.1
  • Multiline commands: DCL, LLO, SDC, GET, GTL, UNT, UNL, SPE, SPD
  • Uniline commands: IFC, REN, EOI, SRQ, ATN
  • Interface functions: SH1, AH1,T5, TE0, L4, LE0, SR1, RL1, PP0, DC1, DT1, C0, E1
• Display: Dual-line vacuum fluorescent
  • 1st line: 20-character alphanumeric
  • 2nd line: 32-character alphanumeric
• Rear-panel connectors
  • IEEE-488
  • 8-pin micro-DIN connector for digital I/O
  • 8-pin micro-DIN for Trigger Link
  • 8-pin micro-DIN for Trigger Link expansion
  • BNC for External Trigger
  • BNC for Channel Ready