Tektronix BSA125C

128 Visitors viewed Avalon Test Equipment ads in the last 30 Days

The BERTScope™ BSA Series Bit Error Rate Testers provide a new approach to signal integrity measurements of serial data systems. Perform bit error ratio detection more quickly, accurately, and thoroughly, by bridging eye diagram analysis with BER pattern generation. The BERTScope BSA Series lets you easily isolate problematic bit and pattern sequences, then analyze further with seven types of advanced error analysis that deliver unprecedented statistical measurement depth.

• Pattern Generation and Error Analysis, highspeed BER Measurements up to 26 Gb/s
• Integrated Stress Generator for stressed eye sensitivity (SRS) and jitter tolerance compliance testing
• Integrated BER correlated eye diagram analysis with pass/fail masks for PCI Express, USB, SATA and other serial standards
• Error Location and BER contour analysis on PRBS and other digital signals up to 26 GB/sec
• Optional Jitter Map provides fast jitter decomposition, accurate stress calibration at the DUT input
• Optional Digital Pre-emphasis Processor provides user controlled pre-emphasis on pattern generator supplied data
• Optional Clock Recovery Units provide clock recovery up to 28.6 Gb/s

Characteristics of the BSA125C (Error Detector):

• Clock input frequency range: 0.1 - 12.5 Gb/s
• Clock/data delay
  • Range up to 1.1 GHz: 30 ns
  • Range above 1.1 GHz: 3 ns
  • Resolution: 100 fs
• Data input:
  • Data rate range: 0.1 - 12.5 Gb/s
  • Configuration: Differential
  • Format: NRZ
  • Polarity: Normal or Inverted
  • Threshold Alignment: Can auto-align to differential crossing point
  • Maximum input signal swing: 2 Vp-p
  • Intrinsic Transition Time: 16 ps typical, 10/90%, single ended (equivalent to >20 GHz detector bandwidth). Measured at input, ECL levels
  • Hardware patterns: Industry-standard Pseudo-random (PRBS) of the type 2^{n – 1} where n = 7, 11, 15, 20, 23, 31
  • RAM pattern user defined: 128 bits to 128 Mb, 128-bit increments
  • Ram pattern library: Wide variety including SONET/SDH, Fibre Channel based such as k28.5, CJTPAT; 2ⁿ patterns where n = 3, 4, 5, 6, 7, 9; Mark Density patterns for 2ⁿ where n = 7, 9, 23; and many more
  • RAM pattern capture: Capture incoming data up to 128 Mb in length. Edit captured data, send to pattern generator, error detector, or both
  • Capture modes: Capture by length—1 to 1,048,576 words, 1-word default, words 128 bit in length; Capture by triggers—Captures when “Detector Start” on rear panel goes high, to maximum allowable length or until input goes low; Capture by length from trigger—Capture by length initiated from “Detector Start” input, to pre-specified length
  • Synchronization: Auto-resync—User-specified number of 128 bit words containing 1 or more errors per word initiates a re-sync attempt; Manual—User initiates re-sync
  • Pattern matching: Grab ‘n’ Go—Error detector captures specified pattern length and compares next instances to find match (Fast method, but susceptible to ignoring logical errors); Shift-to-Sync—Error detector compares incoming pattern with reference RAM pattern, looks for match, if none found shifts pattern by one bit and compares again (Slower but most accurate method)
  • Error Detector Basic Measurements: BER, Bits Received, Re-syncs, Measured Pattern Generator and Error Detector Clock Frequencies
• Error Correlation Marker Input (Error Analysis): Allows an external signal to provide a time-tagged marker to be placed in the error data set
  • Logic Family: LVTTL (<0.5 V Low, >2.5 V High)
  • Threshold: +1.2 V
  • Minimum Pulse Width: 128 clock periods
  • Maximum Repetition Rate: 512 serial clock periods
  • Maximum Frequency: <4000 markers/s recommended
• Blank input: Useful for recirculating loop fiber experiments or during channel training sequences. Causes errors to be ignored when active. Bit count, error count, and BER not counted. No re-sync occurs when counting is re-enabled
  • BERTScope Burst Analysis Timing: BERTScope word size is 128 bits
  • Logic Family: LVTTL (<0.5 V Low, >2.5 V High)
  • Threshold: +1.2 V
  • Minimum Pulse Width: 128 clock periods
  • Maximum Repetition Rate: 512 serial clock periods
• Error output: Provides a pulse when an error is detected. Useful for triggering an alarm while doing long-term monitoring, etc
  • Minimum Pulse Width: 128 clock periods
  • Transition Time: <500 ps
  • Output Levels: 1000 mV nominal (0 V to 1 V low-high)
• Trigger output: Provides a pulse trigger to external test equipment
  • Modes: Divided Clock Mode—Pulses at 1/256th of the clock rate; Pattern Mode—Pulse at a programmable position in the pattern (PRBS), or fixed location (RAM patterns)
  • Minimum Pulse Width: 128 clock periods (Divided Clock Mode); 512 clock periods (Pattern Mode)
  • Transition Time: <500 ps
  • Output Levels: >300 mV amplitude, 650 mV offset
• Detector start input (rear panel)
  • Amplitude: LVTTL (<0.5 V Low, >2.5 V High)
  • Threshold: +1.2 V
  • Minimum Pulse Width: 128 serial clock periods
  • Maximum Repetition Rate: 512 serial clock periods
• Supported interfaces
  • DVI/VGA display
  • USB 2.0 (6 total, 2 front, 4 rear)
  • 100BASE-T Ethernet LAN
  • IEEE-488 (GPIB)
  • Parallel printer
  • Serial RS-232
  • PS-2 mouse/keyboard combined connector