Used Keysight Agilent 83712A for sale by Testwall Ltd | used-line.com
SPECIAL OFFERS
Request Cart (0)
Watchlist (0)
Watchlist (0)
HOME Test and Measurement Generators Synthesized CW Generators Keysight Technologies (Agilent HP) 83712A For Sale Keysight Agilent 83712A

Keysight Agilent 83712A

90 Visitors viewed Testwall Ltd ads in the last 30 Days

Send Request
Keysight Agilent 83712A

 Add to request cart
Send to a Friend
Flag of IrelandEquipment Location: Ireland      
View Description>
Hide Description

Description of Keysight Agilent 83712A

Categories: Generators, Synthesized CW Generators

Manufacturer: Keysight Technologies (Agilent HP)

Model: 83712A

Condition: Used

Seller: Testwall Ltd

Keysight (Agilent) 83712A

Synthesized CW Generator, .01 – 20 GHz


The Agilent HP 83712A Synthesized CW Generator set a high standard for performance for an affordable price. The HP 83712A Signal Generator features fundamental oscillators and switched low-pass filters which deliver +14 dBm), while spectral purity is maintained even at high power levels (typical output power at frequencies below 1 GHz is +20 dBm).Features of the HP 83712A Signal Generator include:

  • Frequency range: .01 to 20 GHz
  • High stability time base for frequency accuracy
  • Low SSB phase noise for out-of-channel tests
  • High power output for driving the LO port of mixers
  • Low output power with option 1E1 for receiver sensitivity and SINAD measurements

    •     

    Product specifications of Keysight Agilent 83712A (From Used-Line T&M Specifications)

    • Launch Date
    • Alternative E8257D PSG Analog Signal Generator
    • Status Discontinued by Manufacturer

    The HP 83712A synthesized CW generator has a carrier frequency range of 10 MHz to 20 GHz.

    • Frequency
      • Range: 0.01 to 20.0 GHz
      • Resolution: 1 kHz, 1 Hz with option
      • Aging rate: <1.0 x 10-8/day after 72 hours, <1.5 x 10-9/day after 24 hour warmup - with option
      • Frequency switching time: <50 ms to within 1 kHz
    • RF output
      • Maximum leveled output power: +13 dBm at 0.01 - 1 GHz, +11 dBm at 1-20 GHz (+10 dBm with option)
      • Minimum leveled output power: 0 dBm, -90 dBm with option
      • Display resolution: 0.01 dB
      • Flatness: ±0.5 dB for power ≥-90 dBm, ±0.7 dB for power <-90 dBm (The use of Type-N RF connectors above 18.0 GHz degrades specification typically by 0.2 dB)
      • Level switching time: <17 ms (without step attenuator range change)
      • Output SWR: <2.0:1 nominal
    • Harmonics: <-55 dBc at output levels <+6 dBm, 0.01 to 1 GHz; <-50 dBc at output levels <+6 dBm, 1 to 20 GHz
    • Non-harmonic spurious: <-60 dBc (≥3 kHz), <-50 dBc (<3 kHz)
    • Residual FM: At 1 GHz, <15 Hz in 50 Hz to 15 kHz bandwidth. Residual FM decreases 6 dB per octave below 1 GHz
    • AM noise floor: (at 0 dBm and offsets greater than 5 MHz from carrier) <-150 dBm/Hz, 1-20 GHz; <-140 dBm/Hz, 0.01-1 GHz
    • Front panel connectors
      • RF Output: The standard front panel RF Output connector is a Type-N precision connector. When Option 1E9 is installed, this front panel connector is a 3.5 mm precision connector. The nominal source impedance is 50 Ω
      • ALC In: This front panel BNC connector allows the synthesizer to be externally leveled. It is used with external power meter leveling or external diode leveling. The leveling signal at this input must be in the ±1 V range. The nominal input impdeance is 150 Ω. The damage level is ≥+12 V or ≤-12 V
    • Rear panel connectors
      • 10 MHz Input: Accepts a 10 MHz ±100 Hz, 0 to +10 dBm, external reference signal for operation from an external high stability timebase. Nominal input impedance is 50 Ω
      • 10 MHz Output: Outputs the 10 MHz reference signal, nominally at +3 dBm, for use as an external reference signal. Nominal source impedance is 50 Ω
      • 0.5 V/GHz Output: Supplies a voltage proportional to output frequency for use with mm-wave frequency multipliers, including the 83550 Series Millimeter Wave Source Modules
    • Options
      • 1E1: Output Step Attenuator
      • 1E2: Internal AM and FM/ΦM sources
      • 1E5: High stability timebase
      • 1E8: 1 Hz frequency resolution
      • 1E9: 3.5 mm RF output connector (male APC-3.5)

    View Similar Listings
    Hide Similar Listings

    Send a Request

    To: Testwall Ltd
    Optional Fields
                
                
                

    About Testwall Ltd

    Send to a Friend

    Recently Viewed Products